Shopsmith Mark VII 7 manual 75 pages gloss protective covers comb bound LAY FLAT

Description: Shopsmith Mark VII 7 manual 75 pages gloss protective covers comb bound LAY FLAT 75 pages gloss protective covers comb boundNew reproductionGlossy protective covers front and backHeavy card stock front and back covers.Comb binding8 1/2 X 11" format, lay flat when openMade in the USALocated on computer 1 fileManual covers the following:TABLE OF CONTENTS WE KNOW YOU ARE ANXIOUS TO USE YOUR NEW SHOPSMITH - BUT.................................................................. 2 SPEED DIAL SETTING ........................................................................................................................................... 2 TABLE OF CONTENTS............................................................................................................................................... 3 MARK VII NOMENCLATURE................................................................................................................................. 7 STANDARD ATTACHMENTS................................................................................................................................. 8 PLUG-IN INSTALLATION ...................................................................................................................................... 8 CHECKING FOR ACCURACY................................................................................................................................ 12 1 - AT "0" TRUNNION SETTING, THE TABLE MUST BE SQUARE TO THE SAW BLADE ................................... 12 IF TABLE, WITH TRUNNION SET AT "0," IS NOT EXACTLY 90 DEGREES TO SAW BLADE ............................... 12 2 TABLE SLOTS MUST BE PARALLEL TO SAW ................................................................................................ 12 IF TABLE SLOTS ARE NOT PARALLEL TO SAW BLADE .................................................................................... 13 3 THE MITER GAUGE, WHEN SET AT 90 DEGREES, MUST BE AT RIGHT ANGLES TO THE TABLE SLOTS. ...... 13 IF MITER GAUGE, AT 90 DEGREE SETTING, IS NOT EXACTLY SQUARE TO BLADE......................................... 14 4 THE RIP FENCE, WHEN LOCKED, MUST BE PARALLEL TO THE TABLE SLOTS.............................................. 14 IF RIP FENCE IS NOT EXACTLY PARALLEL TO TABLE SLOTS............................................................................ 14 5 THE EXTENSION TABLE MUST BE ALIGNED WITH SAW TABLE .................................................................. 14 IF IT IS NOT IN LINE ACROSS THE FRONT: ..................................................................................................... 14 IF IT IS NOT PARALLEL TO MAIN TABLE AFTER ABOVE CHECKS.................................................................... 15 SHOPSMITH 10-INCH SAW.................................................................................................................................... 16 NOMENCLATURE............................................................................................................................................... 16 HOW TO USE THE TABLE SAW .......................................................................................................................... 17 POSITIONING THE POWER HEAD.................................................................................................................. 17 MOUNTING THE SAW BLADE........................................................................................................................ 17 POSITIONING THE TABLE .............................................................................................................................. 17 BLADE PROJECTION....................................................................................................................................... 18 BLADE TO FENCE SETTINGS........................................................................................................................... 18 CROSSCUTTING ............................................................................................................................................. 19 MITER GAUGE SAFETY GRIP.......................................................................................................................... 19 MITER CUTS................................................................................................................................................... 19 CUTTING OFF DUPLICATE LENGTHS.............................................................................................................. 20 RIPPING......................................................................................................................................................... 20 BEVEL RIPPING .............................................................................................................................................. 21 CROSS BEVELING........................................................................................................................................... 22 COMPOUND ANGLE CUTS............................................................................................................................. 22 THE EXTENSION TABLE.................................................................................................................................. 22 SAW BLADES.................................................................................................................................................. 23 ARBORS ......................................................................................................................................................... 24 DADO TOOLS................................................................................................................................................. 24 MAGNA MOLDER .......................................................................................................................................... 25 SAW GUARDS-OPTIONAL .............................................................................................................................. 25 MITER GAUGE EXTENSION............................................................................................................................ 26 SHOPSMITH 16 1/2 INCH DRILL PRESS.................................................................................................................. 26 NOMENCLATURE............................................................................................................................................... 26 HOW TO USE THE DRILL PRESS ......................................................................................................................... 27 SETTING UP ................................................................................................................................................... 27 DRILLING ....................................................................................................................................................... 27 CONTROLLED DEPTH DRILLING..................................................................................................................... 28 PARALLEL DRILLING....................................................................................................................................... 28 JIG DRILLING.................................................................................................................................................. 29 FLOOR MODEL DRILL PRESS.......................................................................................................................... 29 V-BLOCK DRILLING ........................................................................................................................................ 30 MORTISING ................................................................................................................................................... 30 SHOPSMITH MARK VII SHAPER......................................................................................................................... 31 SETTING UP ................................................................................................................................................... 31 ROUTING WITH SHOPSMITH............................................................................................................................. 32 SHOPSMITH HORIZONTAL DRILL........................................................................................................................... 33 HOW TO USE THE HORIZONTAL DRILL.............................................................................................................. 33 DRILLING FOR BUTT DOWEL JOINTS ............................................................................................................. 33 END DRILLING................................................................................................................................................ 33 JIG DRILLING.................................................................................................................................................. 33 CONCENTRIC DRILLING ................................................................................................................................. 34 OTHER OPERATIONS WITH HORIZONTAL SPINDLE........................................................................................... 34 WIRE BRUSHING................................................................................................................................................ 35 POLISHING AND BUFFING................................................................................................................................. 35 SHOPSMITH 16 1/2 INCH BY 34 INCH LATHE........................................................................................................ 37 NOMENCLATURE............................................................................................................................................... 37 HOW TO USE THE LATHE................................................................................................................................... 37MOUNTING SPINDLE WORK ............................................................................................................................. 38 ADJUSTING TOOL REST ..................................................................................................................................... 39 OFFSET TURNING .............................................................................................................................................. 39 TURNING TOOLS ............................................................................................................................................... 40 LATHE WORK ACCESSORIES .............................................................................................................................. 40 SHOPSMITH 10 INCH DISC SANDER ...................................................................................................................... 41 NOMENCLATURE............................................................................................................................................... 41 HOW TO USE THE DISC SANDER ................................................................................................................... 41 DRUM SANDER.............................................................................................................................................. 44 SANDPAPER................................................................................................................................................... 44 SHOPSMITH SPEED CAM-LOCKS ........................................................................................................................... 45 MAINTENANCE AND LUBRICATION ...................................................................................................................... 45 TUBULAR WAYS................................................................................................................................................. 45 BED TUBES......................................................................................................................................................... 45 QUILL................................................................................................................................................................. 45 BEARINGS.......................................................................................................................................................... 45 CAM-LOCKS ....................................................................................................................................................... 45 ALL METAL SURFACES ....................................................................................................................................... 46 OILING PROCEDURE .......................................................................................................................................... 46 SLIDING SHEAVES.......................................................................................................................................... 46 GENERAL ....................................................................................................................................................... 46 OILING INTERMEDIATE SHAFT ...................................................................................................................... 46 OILING MOTOR SHAFT .................................................................................................................................. 46 ADDENDUM 1 - Supplemental information not in original manual ..................................................................... 47 Speed Changer Mark VII ................................................................................................................................... 47 Split Sheave Sets........................................................................................................................................... 47 Table Assembly Nomenclature ......................................................................................................................... 48 Shaper Assembly Nomenclature....................................................................................................................... 48 Forward – Reverse – Safety Key Lock ............................................................................................................... 49 Rack Advance Mechanism ................................................................................................................................ 49 Inter-Latch Button............................................................................................................................................. 49 Eccentric for Lathe Tapering Adjustment ......................................................................................................... 50 Lathe Tapering Eccentric with Live Center........................................................................................................ 50 Levelling Block used for Pocket Screw Hole...................................................................................................... 50Using Mortising Hold Down.............................................................................................................................. 51 PARTS MANUAL .................................................................................................................................................... 52 Mark VII Headstock – PM2................................................................................................................................ 53 Mark VII Headstock Drive, Motor and Housing – PM4..................................................................................... 54 Mark VII Headstock Quill, Speed Control and Rack Advance – PM6 ................................................................ 55 Mark VII Base and Bed – PM8........................................................................................................................... 56 Mark VII Carriage and Table – PM10 ................................................................................................................ 56 Mark VII Fence, Miter Gauge and Grip – PM12................................................................................................ 57 Mark VII Tailstock, Tool Rest, Centers, Arbors, Saw & Sanding Disc – PM14................................................... 58 PART ILLUSTRATION REFERENCE NUMBERS TO PART NUMBERS AND DESCRIPTIONS........................................ 59 501210 A.O. Smith Motor with External Motor Start Relay Wiring ..................................................................... 72 507231 A.O. Smith Motor with Internal Centrifugal Motor Start Switch............................................................. 73 507232 G.E. Motor with Internal Centrifugal Motor Start Switch........................................................................ 74 MARK VII SPEED CHART ........................................................................................................................................ 75

Price: 23.35 USD

Location: Wilton, Maine

End Time: 2023-12-07T12:12:57.000Z

Shipping Cost: N/A USD